G
Availability of solicitations, FAR 5.102(d) applies, as our office no longer issues solicitations or amendments in paper form.
Solicitation will be posted on https://www.dibbs.bsm.dla.mil/ Detailed system requirements and instructions for registration can be found on the DLA DIBBS Home Page accessed on https://www.dibbs.bsm.dla.mil/. A few highlights of the information that will be found include: 1. On the DLA Internet Bulletin Board System (DIBBS) Home Page, click the VENDOR REGISTRATION link to begin the registration process. 2. In order to register for access to secure portions of DLA DIBBS, the company you are representing must already be registered in the Central Contractor Registration (CCR) system. 3. A Commercial and Government Entity (CAGE) Code registration will be processed immediately. A User ID will appear on the registration screen and a password will be sent separately to the email address of the Super User. If a CAGE is already registered on DLA DIBBS, the name and email address of the Super User will be provided. The Super User should be contacted to set-up additional accounts, logons and passwords for their CAGE. DIBBS Super User * If your CAGE has already been registered on DIBBS, the name and email address of the person designated as your super user will be provided. * The representative who starts the DIBBS registration process has the option to accept their CCR registration POC as the DIBBS super user, or they can designate themselves or another person to act as the super user for the CAGE. * The super user acts as the account administrator for a CAGE. They can add up to ninety-eight (98) additional users, provide user IDs and passwords, modify existing users, and control the login status of each user for their CAGEs through My Account (Account Maintenance).
The Defense appropriations and authorization acts and other statutes (including what is commonly referred to as "The Berry Amendment") impose restrictions on the DoD's acquisition of foreign products and services. Generally, Clothing and Textile items (as defined in DFARS clause 252.225-7012) and "specialty metals" (as defined in DFARS clause 252.225-7014), including the materials and components thereof (other than sensors, electronics, or other items added to, and not normally associated with clothing), must be grown, reprocessed, reused, melted or produced in the United States, its possessions or Puerto Rico, unless one of the DFARS 225.7002-2 exceptions applies.
DLA Troop Support has developed a web-based system that allows manufacturers the ability to request specifications, patterns and drawings on our contracting page. To request technical data for DLA Troop Support Clothing and Textiles (C&T) solicitations, use the following link to the DLA Troop Support C&T Technical Data Repository area at
http://www.troopsupport.dla.mil/Portal/sreqfrm.aspx
ADDITIONAL INFORMATION FOR A-A-55098:
.
CLOTHING, LEATHER: TYPE I, CLASS 2, APRON,
SPLIT LEG, SHALL BE MADE IN ACCORDANCE WITH
A-A-55098 DATED 04 DECEMBER 1992
AND DRAWING 2-1-522
INTERIM CHANGES TO A-A-55098:
PAGE 3, PARAGRAPH 3, "THREAD", DELETE IN ITS
ENTIRETY AND SUBSTITUTE:
"THREAD. THE THREAD SHALL BE SPUN PARA-ARAMID
INTERMEDIATE MODULUS OR COTTON THREAD USED FOR
MACHINE AND HAND SEWING. THE THREAD SHALL BE A
DYED KHAKI P-1, C. A. 66019 AND SHALL CONFORM TO
THREAD SIZES LISTED BELOW:
.
PAGE 3, PARAGRAPH 4, LEATHER, LINE 4, DELETE
"NATURAL" AND SUBSTITUTE "NATURAL AS PRODUCED
BY THE TANNING AGENTS.".
.
PAGE 3, AFTER "LABELING" PARAGRAPH, ADD THE
FOLLOWING NEW PARAGRAPH;
"BAR CODE LABEL/TAG. EACH ITEM SHALL BE
INDIVIDUALLY BAR CODED WITH A TYPE VIII,
CLASS 17, LABEL/TAG OF DDD-L-20. THE LABEL/TAG
SHALL BE LOCATED SO THAT IT IS COMPLETELY
VISIBLE ON THE ITEM WHEN IT IS FOLDED AND/OR
PACKAGED AS SPECIFIED AND SHALL CAUSE NO DAMAGE
TO THE ITEM.".
.
PAGE 6, "DEFECTS CONT" PARAGRAPH, AT THE END OF
THE PARAGRAPH ADD; "BAR CODE OMITTED OR NOT
READABLE BY SCANNER, HUMAN READABLE INTERPRE-
TATION (HRI) OMITTED OR ILLEGIBLE, NOT VISIBLE
ON FOLDED, PACKAGED ITEM, OR CAUSES DAMAGE TO
ITEM.".
.
PAGE 7, UNDER PACKAGING, DELETE "OVERSEAS".
.
PAGE 8, AFTER MARKING, DELETE "DOMESTIC" AND
DELETE PARAGRAPH THAT FOLLOWS PERTAINING TO
"PACKAGING, PACKING...MARKING" IN ITS ENTIRETY.
.
ADDITIONAL INFORMATION FOR FED-STD-191:
FED-STD-191A NOTICE 7, DATED AUGUST 9, 2000 IS HEREBY INACTIVE FOR NEW
DESIGN. WHEN NOT USING FED-STD-191, SEE INTERIM CHANGES TO END ITEM
SPECIFICATION FOR REPLACEMENT ASTM.
INTERIM CHANGES TO FED-STD-191A:
TEST METHOD 5202, PARA. 5.3, DELETE FIRST SENTENCE AND SUBSTITUTE: "THE
SPECIMEN SHALL BE CLAMPED FIRMLY, WITH ONE END FLUSH WITH THE OUTER EDGE
OF THE VISE, SUCH THAT ONE INCH OF SPECIMEN LIES WITHIN THE CLAMP AND
ONE INCH OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION (FACE OF
THE VISE), AND WITH THE LONG EDGE PARALLEL TO THE FACE OF THE DIAL
PLATE".
TEST METHOD 5309.1 ABRASION RESISTANT OF TEXTILE WEBBING. PAGE 1, PARA
4.1.2,LINE 4: DELETE "B-97" AND SUBSTITUTE "B-91".
THE FOLLOWING METHODS ARE IDENTIFIED AS SPECIFYING OZONE DEPLETING
SUBSTANCES: 1100, 1200, 1240, 1400, 1410, 1500, 1510,1520,1530, 1540,
AND 1550. PARA 5.1 OF THESE TEST METHODS REQUIRE THE USE OF 1,1,1-
TRICHLOROETHANE, ALCOHOL OR ETHER. 1,1,1-TRICHLORETHANE IS AN OZONE
DEPLETING SUBSTANCE (METHYL CHLOROFORM) AND IS THEREFORE PROHIBITED. THE
USE OF EITHER ALCOHOL OR ETHER IS REQUIRED WHEN THESE METHODS ARE IN
BASIC OR ANY REFERENCED DOCUMENT.
METHOD 5202, STIFFNESS OF CLOTH, DIRECTIONAL; CANTILEVER BENDING METHOD.
PAGE 2, PARA. 5.3 DELETE FIRST SENTENCE AND SUBSTITUTE WITH THE
FOLLOWING: "THE SPECIMEN SHALL BE CLAMPED FIRMLY, WITH 1 END FLUSH WITH
THE OUTER EDGE OF THE VISE, SUCH THAT 1" OF THE SPECIMEN LIES WITHIN THE
CLAMP AND 1" OF THE SPECIMEN EXTENDS BEYOND THE CENTER OF ROTATION
(INNER FACE OF THE VISE) AND WITH THE LONG EDGE PARALLEL TO THE FACE OF
THE DIAL PLATE."
METHOD 5556.1, MOBILE LAUNDRY EVALUATION FOR TEXTILE MATERIALS, PAGE 5,
PARA. 5.2.2, LINE 8: DELETE SENTENCE BEGINNING WITH "THE SPECIMENS AND
BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THE FOLLOWING: "THE
SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND
PLACED IN A PRE-HEATED DRYER HAVING A STACK TEMPERATURE OF 140-180 DEG.
F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE
TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 45-60
MINUTES OR UNTILSAMPLES ARE DRY IN A ROTATING TUMBLE DRYER."
PAGE 5, PARA. 5.2.3, LINE 8: DELETE SENTENCE BEGINNING WITH "THE
SPECIMENS AND BALLAST" IN ITS ENTIRETY AND SUBSTITUTE WITH THEFOLLOWING:
"THE SPECIMENS AND BALLAST SHALL BE SEPARATED, OPENED TO FULL WIDTH AND
PLACED IN A PRE-HEATED DRYER HAVING A STACKTEMPERATURE OF 140-180 DEG.
F. THIS TEMPERATURE RANGE CORRESPONDS TO A SETTING OF "HIGH" ON THE
TEMPERATURE INDICATOR ON THE DRYER. DRYING SHALL CONTINUE FOR 35-40
MINUTES OR UNTIL SAMPLES ARE DRY."
METHOD 5931, ELECTROSTATIC DECAY OF FABRICS; DETERMINATION OF PAGE 1,
PARA. 3: AFTER NUMBER OF DETERMINATIONS ADD "PER SAMPLE UNIT". PAGE 1,
PARA. 4: DELETE "APPARTUS" AND SUBSTITUTE "APPARATUS". PAGE 1, PARA.
5.1, LINE 3: AFTER "AT" DELETE"APPROXIMATELY".
PAGE 2, PARA. 5.2, LINES 2, AND 5: AFTER "OF" ADD "+-". LINE 6: AFTER
"TO" ADD "+-".
PAGE 2, PARA. 5.3: DELETE IN ITS ENTIRETY AND SUBSTITUTE WITH THE
FOLLOWING:"5.3 MOUNT A SPECIMEN TIGHTLY ACROSS THE ELECTRODES, CENTERING
IT OVER THE SENSOR OPENING. THE SURFACE OF THE TEST SPECIMEN (BACK OR
FRONT) SHALL FACE THE SENSOR. RECORD (OPTIONAL) THE RESIDUAL CHARGE
LEVEL ON THE SAMPLE AS SEEN BY THE SENSOR, INCLUDING POLARITY.
NOTE THAT TEST SAMPLES WITH THE RESIDUAL CHARGE LEVELS OF LESS +500
VOLTS YIELD THE BEST RESULTS. APPLY +5000 VOLTS TO THEELECTRODES FOR A
PERIOD OF 20 SECS. AT THE END OF THE 20 SECOND PERIOD, THE HIGH VOLTAGE
(5000 VOLTS) SHALL BE TURNED OFF ANDTHE SPECIMENS IMMEDIATELY GROUNDED.
THE VOLTAGE BEHAVIOR OF THE SPECIMEN WITH RESPECT TO TIME SHALL BE
PLOTTED ON THE RECORDER. NOTE: IN SOME CASES, THE TEST EQUIPMENT WILL
DISPLAY VOLTAGE AND DECAY TIME INFORMATION AND A CHART RECORDER IS NOT
NECESSARY."
PAGE 2, PARA. 5.4, LINE 3: DELETE SENTENCE BEGINNING WITH "IF THE
SPECIMEN DID" IN ITS ENTIRETY.
PAGE 2, PARA. 5.5: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH
THE FOLLOWING: "RECORD THE MAXIMUM VOLTAGE LEVEL(INCLUDING POLARITY) AND
DECAY TIME TO 10% OF THE MAXIMUM VOLTAGE LEVEL ACHIEVED."
PAGE 2, PARA. 5.6, LINE 1: ADD THE FOLLOWING PRIOR TO 1ST SENTENCE:
"REVERSE VOLTAGE POLARITY REPEAT MEASUREMENT, ANDRECORD RESULTS."
PAGE 3, PARA. 6.6: DELETE PARAGRAPH IN ITS ENTIRETY AND SUBSTITUTE WITH
THE FOLLOWING: "THE AVERAGE TIME TO DECAY TO 10%OF THE MAX VOLTAGE SHALL
BE INCLUDED FOR EACH OF THE WARP & FILLING DIRECTIONS, AS WELL AS THE
OVERALL AVERAGE, FOR EACHFABRIC TESTED. THESE WILL BE OBTAINED BY
AVERAGING THE TEST RESULTS (ABSOLUTE VALUE OF) TOGETHER FOR BOTH
VOLTAGEPOLARITIES. UNLESS OTHERWISE STATED IN THE REQUIREMENTS
DOCUMENT, THE FABRIC SHALL BE CONSIDERED ACCEPTABLE IF THEAVERAGE
MAXIMUM VOLTAGE IN BOTH THE WARP AND FILLING DIRECTIONS IS LESS THAN
4000 VOLTS, AND THE AVERAGE DECAY TIME (TO 10% MAXVOLTAGE) IS GREATER
THAN 0.5 SECONDS IN BOTH THE WARP AND FILLING DIRECTIONS. IT SHALL BE
INDICATED WHETHER THE FABRIC ISACCEPTABLE OR NON-ACCEPTABLE."
PAGE 3, PARA. 7.1, SECOND COLUMN, LINE 2: DELETE 406C AND SUBSTITUTE
WITH "406D".
AFTER PARA. 7.1, ADD THE FOLLOWING: "7.2 NOTE: IF THE MODEL 406D STATIC
DECAY METER, OR EQUIVALENT, IS USED, A CHART RECORDER ISNOT MANDATORY
FOR THE TEST."
(Ref. T0215)
INTERIM CHANGES FOR PNP FUNGICIDE REQUIREMENTS:
.
SECTION 3 OF THE SPECIFICATION REFERENCED:
DELETE ALL CURRENT REFERENCES TO THE FUNGICIDE
PARANITROPHENOL.
UNLESS OTHERWISE SPECIFIED, ONE OF THE FOLLOWING
FUNGICIDES IS REQUIRED:
1. PARANITROPHENOL:
THE LEATHER SHALL CONTAIN NOT LESS THAN 0.18 AND
NOT MORE THAN 0.70 PERCENT PARANITROPHENOL
FUNGICIDE WHEN TESTED AS SPECIFIED BELOW
2. VITASAN:
THE LEATHER SHALL CONTAIN NOT LESS THAN 1.6 AND
NOT MORE THAN 5.0 PERCENT OF THE ACTIVE INGREDI-
ENT ORTHO-PHENYLPHENOL, WHEN TESTED AS SPECIFIED
BELOW.
3. AMICAL:
THE LEATHER SHALL CONTAIN NOT LESS THAN 300PPM
AND NOT MORE THAN 1000PPM OF ACTIVE INGREDIENT
DIIODOMETHYL-P-TOLYSULFONE, WHEN TESTED AS
SPECIFIED BELOW.
.
TEST METHODS FOR ABOVE FUNGICIDE TREATMENTS
1. PARANITROPHENOL:
THE TEST FOR CONCENTRATION OF PARANITROPHENOL IN
THE LEATHER SHALL BE CONDUCTED IN ACCORDANCE
WITH TEST METHOD 6711 OF FED-STD-311.
.
2. VITASAN:
THE TEST METHOD TO DETERMINE ORTHO-PHENYLPHENOL
CONCENTRATION IN LEATHER SHALL BE CONDUCTED IN
ACCORDANCE WITH METHOD I, TYPE I OF MIL-L-8067.
.
3. AMICAL:
THE TESTING TO DETERMINE THE CONCENTRATION OF
AMICAL IN THE LEATHER SHALL BE CONDUCTED IN
ACCORDANCE WITH THE FOLLOWING TEST PROCEDURE:
DRYING AND GRINDING. BEFORE GRINDING THE
LEATHER MUST BE CUT INTO SMALL PIECES, APPROX-
IMATELY 1/2 INCH BY 1/2 INCH, WHICH IN TURN
ARE DRIED AT ROOM TEMPERATURE OVERNIGHT. FOR
CHEMICAL ANALYSIS GRIND THE DRIED LEATHER PIECES
IN ACCORDANCE WITH PARAGRAPH 6.3.7 OF ASTM
2813 STANDARD PRACTICE FOR PHYSICAL AND
CHEMICAL TESTS.
HPLC DETERMINATION.
STOCK STANDARD PREPARATION. WEIGH ACCURATELY
APPROXIMATELY 100 MG OF DIIODOMETHYL-PARA-
TOLYLSULFONE INTERNAL REFERENCE STANDARD (IRS),
(SEE 6.7.1) INTO A 100 ML VOLUMETRIC FLASK. ADD
APPROXIMATELY 50 ML OF ACETONITRILE, STOPPER AND
SONICATE TO AID DISSOLUTION (ABOUT 1 MINUTE).
DILUTE TO VOLUME WITH ACETONITRILE.
WORKING STANDARDS PREPARATION. TRANSFER 3ML
ALIQUOTS OF THE STOCK STANDARD PREPARATION TO
25,50,100 AND 250ML VOLUMETRIC FLASKS. DILUTE
TO VOLUME WTIH ACETONITRILE. THESE STANDARDS
CONTAIN APPROXIMATELY 12,30,60 AND 120PPM OF
DIIODOMETHYL-PARA-TOLYLSULFONE.
NOTE: A LOWER STANDARD MAY BE REQUIRED FOR SAM-
PLES CONTAINING VERY LOW LEVELS OF AMICAL. SOL-
UTIONS OF DIIODOMETHYL-PARA-TOLYLSULFONE MUST BE
STORED IN DARKNESS TO PREVENT DEGRADATION. MINI-
MIZE EXPOSURE TO LIGHT DURING PREPARATION AND
USE. THE STANDARD PREPARATIONS MAY BE RETAINED
ONE MONTH.
SAMPLE PREPARATION. ACCURATELY WEIGH APPROXI-
MATELY 4-5G OF SAMPLE INTO A 150ML BEAKER. ADD
75ML-100ML OF ACETONITRILE. COVER SAMPLES WITH
PARAFILM: MIX 24 HOURS ON A MAGNETIC STIR PLATE.
THE FOLLOWING DAY, ALLOW SAMPLES TO SETTLE;
REMOVE NECESSARY EQUIPMENT: (NOTE: SAMPLES MAY
HAVE TO BE DILUTED FURTHER TO FALL WITHIN
STANDARD CURVE.)
HPLC SYSTEM WITH VARIABLE UV DETECTOR AND INTE-
GRATING COMPUTER.
SUITABLE SYRINGE AND GLASSWARE.
A MICRO-BONDAPAK C18 COLUMN (WATERS ASSOCIATES,
P/N 2734) OR EQUIVALENT.
0.45-MICRON POLYCARBONATE FILTERS (NUCLEPORE
CORPORATION, CATALOG NO. 111107) OR EQUIVALENT.
CALCULATOR CAPABLE OF DOING LINEAR REGRESSION.
REAGENTS: ACETONITRILE (CHROMATOGRAPHIC GRADE).
TYPICAL MOBILE PHASE. MIX 550ML OF DISTILLED
WATER, 450ML OF ACETONITRILE. FILTER AND DEGAS
THE SOLUTION. THE CONCENTRATION MAY BE VARIED
TO MEET SYSTEM SUITABILITY REQUIREMENTS WITHIN
THE RANGE 50% TO 40% ACETONITRILE.
TYPICAL CHROMATOGRAPHIC CONDITIONS:
INJECTION VOLUME 20 MICROLITERS
FLOW 2.5 ML/MINUTE
DETECTOR 235 MM
SYSTEM SUITABILITY. INJECT THE HIGHEST WORKING
STANDARD UNTIL 2% AGREEMENT IS REACHED BETWEEN
TWO SUCCESSIVE INJECTIONS. CHROMATOGRAPH FOR
APPROXIMATELY 15 MINUTES. DETERMINE THAT AFTER
THE SOLVENT FRONT ONE IMPURITY PEAK ELUTES BE-
FORE THE MAJOR PEAK. ELUTION FOR MONOIODOMETHYL
PARA-TOLYLSULFONE AND DIIODOMETHYL-PARA-
TOLYLSULFONE IS ABOUT 8.5 MINUTES.
PROCEDURE. INJECT EACH STANDARD AND SAMPLE
PREPARATION IN DUPLICATE ALLOWING EACH INJECTION
TO RUN FOR AT LEAST 15 MINUTES. MEASURE THE
PEAK RESPONSE FOR THE DIIODOMETHYL-PARA-
TOLYLSULFONE . NOTE: THE RUN TIME MAY HAVE
TO BE INCREASED FOR SAMPLES WITH LATE ELUTING
PEAKS. PERFORM A LINEAR REGRESSION OF PEAK RES-
PONSE (AREA) VERSUS CONCENTRATION FOR EACH OF
COMPONENTS.
FOR EACH COMPONENT:
CONCENTRATION (PPM) IN LEATHER CONCENTRATION
(PPM) FROM LINEAR REGRESSION TIMES 75
OVER SAMPLE WT (G)
.
ADD THE FOLLOWING INFORMATION TO THE SECTION 6:
WHEN A FUNGICIDE IS SPECIFIED:
SOURCES SUGGESTED FOR FUNGICIDES ALTERNATE TO
PARANITROPHENOL:
FOR AMICAL AND IRS IS CHEMTAN COMPANY, EXETER NH
03833-0050.
SUGGESTED SOURCE FOR VITASAN IS BLUMBERG CORPOR-
ATION, NEWBURYPORT, MA 01950
.
ADDITIONAL INFORMATION FOR A-A-52094A:
NO ADDITIONAL INFORMATION
(ref. T1481)
ADDITIONAL INFORMATION: FED-STD-751 HAS BEEN
CANCELLED AND REPLACED BY ASTM-D-6193, 4/98
STANDARD PRACTICES FOR STITCHES AND SEAMS.
THIS STANDARD SHOULD BE USED IN PREFERENCE
TO FED-STD-751.
(ref. T0216 - May 18, 2006)
DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS.
PART I AND II, JULY 2000 AND SUPPLEMENT, MARCH 2000
MIL-STD-147 IS HEREBY REINSTATED AS FOLLOWS:
MIL-STD-147E DEPARTMENT OF DEFENSE
16 MAY 2008 STANDARD PRACTICE
PALLETIZED UNIT LOADS
STANDARDS (COMMERCIAL)
ASME-MH1 American Society of Mechanical Engineers (ASME) Pallets, Slip
Sheets, and Other Bases For Unit Loads, for construction of pallets.
MIL-STD-731 IS HEREBY CANCELLED, NOTICE 2 DATED 12/5/95. ASTM-D-6199 -
"STANDARD PRACTICE FOR QUALITY OF WOOD MEMBERS
OF CONTAINERS AND PALLETS" HAS BEEN ADOPTED AS A REPLACEMENT
AS OF 7/29/98.
(ref. T0340 - May 18, 2006)
MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,
AND TENTAGE, GENERAL USE REPLACES DDD-L-20
(Ref. T0451 - June 19, 2007)
INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:
PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-
20" AND REPLACE "MIL-DTL-32075,".
PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE
TYPE VI FINISHED LABEL." UNDER "TEARING
STRENGTH" DELETE: "(LB.) MINIMUM" AND
SUBSTITUTE: "(GNS) MINIMUM."
PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD
"AND THE UNIVERSAL PRODUCT CODE (UPC)
SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."
ADDITIONAL INFORMATION FOR FF-R-556:
.
NO ADDITIONAL INFORMATION FOLLOWS.
.
ADDITIONAL INFORMATION FOR JJ-W-155:
INTERIM STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436, ROLL #3729
(THE FOLIAGE GREEN 502 AREA OF THE PATTERN), AND REFERENCED FOR SHADE
ONLY. THIS STANDARD IS TEMPORARY UNTIL FURTHER NOTICE. THIS APPLIES TO
TYPE I, CLASS 6 AND TYPE I, CLASS 11.
INTERIM SPECIFICATION CHANGES TO JJ-W-155H:
PAGE 8, TABLE I, ACROSS FROM CLASS 3, UNDER MIN. YARNS PER INCH: DELETE
"100" AND SUBSTITUTE "100 12/".
PAGE 10, TABLE I, ACROSS FROM CLASS 29, UNDER MIN. YARNS PER INCH:
DELETE FOOTNOTE "6/" AND SUBSTITUTE FOOTNOTE "10/".
UNDER FOOTNOTE 11/: ADD "12/ 100 YARNS PER INCH OF 24/2 YARN OR 136
YARNS PER INCH OF 40/2 WITH 2 YARNS PER SHED."
PAGE 12, PARA. 3.10.1 DELETE IN ITS ENTIRETY AND SUBSTITUTE "3.10.1
AQUEOUS COPPER-8-QUINOLINOLATE. THE WEBBING SPECIFIED IN 3.10 SHALL BE
MILDEW TREATED WITH AQUEOUS COPPER 8-QUINOLINOLATE OR OTHER APPROVED
AQUEOUS BASED MILDEW INHIBITOR. BECAUSE OF THE TIME NECESSARY TO CONDUCT
FULL EVALUATION, ONLY THOSE TREATMENTS ALREADY APPROVED AND SO LISTED IN
THE INVITATION FOR BIDS OR REQUESTS FOR PROPOSAL SHALL BE CONSIDERED
ACCEPTABLE FOR THE RELATED PROCUREMENT."
PAGE 26, PARA 4.3.1, LINE 8, BETWEEN "...(SEE 6.4)." AND "THE STARTING
GAGE..." INSERT "AS AN ALTERNATE, ASTM-D4964 MAY BE USED TO DETERMINE
ELASTIC LOOP TENSION AT SAME REQUIRED PERCENT ELONGATION AND UNDER SAME
CARRIAGE LOAD PARAMETERS AS SPECIFIED IN TABLE III (I.E. FOR TYPE 1, CI
20 ELASTIC SET CRE CYCLE TO MAXIMUM 30 LBS. AND DETERMINE LOOP TENSION
ON THIRD CYCLIC UPLOAD CURVE AT 50% ELONGATION). IF ALTERNATE TM IS
USED, THEN ALLOW A +10% FACTOR TO MAXIMUM TENSION REQUIREMENT IN TABLE
III."
APPROVED AQUEOUS MILDEW TREATMENTS FOR:
MIL-W-43638 WEBBING, TEXTILE, WOVEN FOR TENT FRAMING;
MIL-W-5665, WEBBING, TEXTILE, COTTON WARP;
MIL-W-530, WEBBING, TEXTILE, COTTON GENERAL PURPOSE, NATURAL OR IN
COLORS;
MIL-T-43566, TAPE, TEXTILE, COTTON OR POLYESTER, GENERAL PURPOSE,
NATURAL OR IN COLORS,
JJ-W-155, WEBBING, TEXTILE, (COTTON,ELASTIC):
PRODUCT SUPPLIER
CUNILATE 2002 MORTON INTERNATIONAL, INC
150 ANDOVER STREET
DANVERS, MA. 01923
TEL: (508-774-3100)
(ref. T0503 - May 19, 2006)
ACCEPTABLE ALTERNATE MILDEW TREATMENT FOR 2,2'
METHYLENE-BIS-(4-CHLOROPHENOL)
1. WHEN A SPECIFICATION SPECIFIES "2,2'
METHYLENE-BIS-(4- CHLOROPHENOL)" MILDEW RESISTANT
TREATMENT FOR COTTON TEXTILE MATERIALS, "RO-59"
IS APPROVED AS AN ALTERNATIVE TREATMENT AND IS
AUTHORIZED FOR USE. THIS CHANGE APPLIES TO
PENDING AND FUTURE CONTRACTS USING TEXTILE
MATERIALS THAT SPECIFY THE SUBJECT MILDEW
RESISTANT TREATMENT.
2. THE PRODUCT MAY BE OBTAINED FROM:
RO-59 INC.
1 CABOT PL #3
STOUGHTON, MA 02072
TELEPHONE (781) 264-1213
POC: MR. RONNIE BENDER
3. THE TEXTILE MATERIALS TREATED WITH RO-59
MILDEW INHIBITOR TREATMENT SHALL BE TESTED IN
ACCORDANCE WITH AATCC TEST METHOD
30 - ANTIFUNGAL ACTIVITY, ASSESSMENT ON TEXTILE
MATERIALS: MILDEW AND ROT RESISTANCE OF TEXTILE
MATERIALS, TEST III. THE TREATED MATERIAL SHALL
NOT EXHIBIT "MACROSCOPIC GROWTH
(VISIBLE TO THE EYE)".
ADDITIONAL INFORMATION FOR PPP-B-636:
FEDERAL SPECIFICATION PPP-B-636 DATED JULY 12, 1981, INCLUDING INTERIM
FEDERAL SPECIFICATION PPP-B-636L DATED JANUARY 1, 1991, IS HEREBY
CANCELLED, AND REPLACED WITH ASTM-D-5118, STANDARD PRACTICE FOR
FABRICATION OF FIBERBOARD SHIPPING BOXES, AND ASTM-D-1974, STANDARD
PRACTICE FOR METHOD OF CLOSING, SEALING AND REINFORCING FIBERBOARD
SHIPPING CONTAINERS.
ADDITIONAL INFORMATION FOR KK-L-2004 WITH INTERIM CHANGES BELOW:
FEDERAL SPECIFICATION KK-L-2004, DATED 22 APRIL, 1989 IS HEREBY
CANCELED. THIS DOCUMENT HAS BEEN SUPERSEDED BY MIL-DTL-32092 LEATHER,
CATTLEHIDE, DEERSKIN AND HORSEHIDE, CHROME TANNED, Nov. 8, 2001.
(ref. T0731 - 5/23/06)
ADDITIONAL INFORMATION FOR MIL-B-286:
.
NO ADDITIONAL INFORMATION FOLLOWS.
.
INTERIM CHANGES TO MIL-DTL-10884H:
PAGE 1, PARA. 1.2, CLASSIFICATION. AFTER "FINISH 5" ADD "FINISH 6 -
WHITE".
PAGE 8, PARA. 3.4.5, DELETE SENTENCES 4 AND 5 IN THEIR ENTIRETY.
PAGE 8, AFTER PARA. 3.4.5, ADD NEW PARA. AS FOLLOWS: "3.4.6 FINISH 6 -
WHITE. REFERENCE PARA. 3.4.5 EXCEPT THE COLOR SHALL BE WHITE."
ADDITIONAL INFORMATION FOR MIL-G-16491:
MIL-G-16491F IS CANCELLED - REPLACED BY NASM 16491.
(ref. T1232 - 6/6/06)
ADDITIONAL INFORMATION FOR DD 81337 2-1-522:
.
NO ADDITIONAL INFORMATION FOLLOWS.